Electrician's Laborer II

The Electricians Laborer II will assist the foreman and journeymen with the day-to-day execution of the following scope:

• Pulling dressing and labeling low-voltage controls communication and signal cabling (CAN bus Ethernet/Profinet fiber where applicable) between Muratec OHT/OHS track segments controllers and OCS interfaces.
• Installing and supporting cleanroom-compatible cable tray conduit and stainless hardware overhead along the AMHS track corridor.
• Material handling: staging wipe-down and transfer of approved cleanroom materials through the airlock to the work area.
• Assisting with megger testing point-to-point continuity and basic pre-energization checks under direct supervision.
• Maintaining a clean organized contamination-controlled work area at all times.

• Report to the Electrical General Foreman / SME and assigned journeyman daily; follow direction precisely and ask questions before guessing.
• Participate in daily pre-task planning (PTP) meetings JSAs and stretch-and-flex; understand the days scope hazards and quality expectations before entering the cleanroom.
• Perform low-voltage cable pulls terminations and dressing under journeyman supervision with focus on neatness labeling and adherence to Muratec installation standards.
• Operate scissor lifts articulating booms and rolling scaffolds safely after certification AMHS track work is overhead work not floor work.
• Maintain accurate timekeeping material usage and daily production reporting to the foreman.
• Keep the work area clean organized and contamination-controlled throughout the shift; clean as you go not at the end of the day.

• Follow gowning glove and tool-control protocols exactly as trained every shift every entry no shortcuts.
• Wipe down all tools materials and consumables at the airlock per the sites contamination control plan (CCP) before bringing anything into the cleanroom.
• Use only cleanroom-approved tools lubricants tape and consumables; if an item is not on the approved list ask the foreman before using it.
• Understand that cutting drilling and cable pulling generate particles; coordinate with the foreman on containment vacuuming and sequencing of dirty work.
• Treat every entry into the cleanroom as a discipline test the protocol does not relax because the work is routine.

• Follow NFPA 70E OSHA and site-specific safety requirements without exception; wear required PPE at all times.
• Comply with all Lockout/Tagout (LOTO) procedures; never bypass share or remove a lock that is not yours.
• Maintain three-point contact on all ladders and lifts; tie off when required; inspect fall protection daily before use.
• Practice slip/trip/fall awareness keep cords hoses and material out of walkways; report and clean up spills and debris immediately.
• Stop work and notify the foreman whenever conditions feel unsafe there is never a penalty for stopping work and the crew will back the call.
• Report all near-misses incidents and injuries to the foreman immediately no matter how minor.

• Install terminate and dress every cable to Muratec specifications and the approved drawings first time every time.
• Support megger logs continuity checks and torque records as directed by the journeyman or foreman.
• Flag damaged material suspect terminations or drawing conflicts to the foreman immediately never bury a quality issue or rework around it.

• Approach this project as an apprenticeship in cleanroom and AMHS work; ask questions take notes and learn the why behind each protocol.
• Build proficiency with megger multimeter clamp meter and basic cable testing tools under journeyman supervision.
• Demonstrate steady progression from supervised execution toward independent task ownership over the life of

• Minimum 2-5 years of electrical experience; recent trade school graduates registered electrical apprentices and entry-level helpers with strong work ethic and basic electrical fundamentals will be considered.
• Basic familiarity with hand tools power tools and standard electrical materials (conduit wire terminations labeling).
• Ability to interpret electrical drawings cable schedules installation details and equipment layouts.
• No prior cleanroom or AMHS experience required but preferred if needed site-specific training will be provided.

• OSHA 10 (Construction) current or willingness to complete on day one NEED TO HAVE PRIOR TO APPLYING TO JOB
• Scissor lift aerial work platform (AWP) and basic fall protection certifications required or willingness to complete site training before working at heights.
• LOTO Authorized Person training required or willingness to complete site training.
• Cleanroom gowning certification site-specific certification will be completed on day one.

• Basic hand-tool and power-tool proficiency: hand benders drills drivers wire strippers crimpers torque tools.
• Familiarity with megger multimeter and clamp meter at a beginner level; ability to learn proper use under journeyman supervision.
• Basic cable pulling dressing and labeling skills; understanding of bend radius support spacing and basic cable management practices.

• Coachable: takes direction asks questions and acts on feedback without ego.
• Reliable: shows up on time every day in full PPE and ready to work.
• Disciplined: follows cleanroom and safety protocols exactly even when no one is watching.
• Detail-oriented: cares about clean labeling neat dressing and accurate work not just getting it done.
• Team-first: supports the journeymen and foremen helps the crew and contributes to a safe productive shift.

• 2-5 years prior experience as a helper or apprentice on industrial data center semiconductor or pharmaceutical cleanroom construction projects.
• Familiarity with low-voltage controls communication cabling (Ethernet fiber) or structured cabling work.

• Ability to wear full cleanroom garments (bunny suit hood booties double gloves safety glasses mask) for full shifts.
• Comfortable working at heights from scissor lifts articulating booms and rolling scaffolds AMHS track work is overhead all da