Production Wax Assembler SSBO

Clackamas, OR - USA

Monthly Salary: Not Disclosed

Posted on: 30+ days ago

Vacancies: 1 Vacancy

Job Summary

MISSION:

To assemble moderately complex wax components including gating systems to produce mold forms to be invested.

PRINCIPAL ACCOUNTABILITIES:

Preparation.

Objective: to inspect patterns and determine assembly methods.

Typical Activities:

Pre-inspects pattern and gating components prior to start of assembly.
Reads and follows technique card assembly instructions which describe assembly steps of a moderately complex nature.

Assembly.

Objective: to accurately assemble multi-component patterns and maintain dimensional integrity.

Typical Activities:

Assembles wax patterns and gating components by means of torch hot pencils and a variety of hand tools.
Welds gates into place by means of torch or hot pencil.
Assembles moderately complex patterns; occasionally uses assembly fixturing to maintain dimensional control and stability.
Manipulates fixture/pattern components to remove configuration discrepancies and verify dimensional integrity.
Smoothes and gauges the area around each assembly contact by means of hot pencil torch or paint seal.
Occasionally modifies gates by reshaping splicing or reducing in order to obtain proper fit.
Occasionally hand fabricates elementary gating from raw stock.
Inspects assemblies during and after the assembly process for defects and quality.

Safety.

Objective: to take responsibility for and demonstrate safe work practices.

Typical Activities:

Adheres to plant and department safety rules.
Safely operates all equipment and tools.
Identifies and reports safety problems.
Performs other tasks as assigned.

TRAINING:

Training is provided on the job.

ENTRY QUALIFICATIONS:

Nine to twelve months of production wax assembly experience preferredORAn equivalent combination of experience and training.
Basic knowledge of assembly techniques methods materials fixturing and construction.
Ability to follow and communicate complex written and verbal instructions and to perform arithmetic calculations.
Demonstrated high degree of manual dexterity.
Ability to lift and/or maneuver objects weighing thirty to fifty pounds and occasionally up to one hundred twenty five pounds.
Ability to work in conditions which may include exposure to noise fumes crowding awkward physical positions abrasions cuts and chemicals.

MAJOR PLANT DIFFERENCES:

LSBO uses Production Wax Assembler B as a training position and does not use level C Assemblers.

MISSION:To assemble moderately complex wax components including gating systems to produce mold forms to be invested.PRINCIPAL ACCOUNTABILITIES:Preparation.Objective: to inspect patterns and determine assembly methods.Typical Activities:Pre-inspects pattern and gating components prior to start of ass...

MISSION:

To assemble moderately complex wax components including gating systems to produce mold forms to be invested.

PRINCIPAL ACCOUNTABILITIES:

Preparation.

Objective: to inspect patterns and determine assembly methods.

Typical Activities:

Pre-inspects pattern and gating components prior to start of assembly.
Reads and follows technique card assembly instructions which describe assembly steps of a moderately complex nature.

Assembly.

Objective: to accurately assemble multi-component patterns and maintain dimensional integrity.

Typical Activities:

Assembles wax patterns and gating components by means of torch hot pencils and a variety of hand tools.
Welds gates into place by means of torch or hot pencil.
Assembles moderately complex patterns; occasionally uses assembly fixturing to maintain dimensional control and stability.
Manipulates fixture/pattern components to remove configuration discrepancies and verify dimensional integrity.
Smoothes and gauges the area around each assembly contact by means of hot pencil torch or paint seal.
Occasionally modifies gates by reshaping splicing or reducing in order to obtain proper fit.
Occasionally hand fabricates elementary gating from raw stock.
Inspects assemblies during and after the assembly process for defects and quality.

Safety.

Objective: to take responsibility for and demonstrate safe work practices.

Typical Activities:

Adheres to plant and department safety rules.
Safely operates all equipment and tools.
Identifies and reports safety problems.
Performs other tasks as assigned.

TRAINING:

Training is provided on the job.

ENTRY QUALIFICATIONS:

Nine to twelve months of production wax assembly experience preferredORAn equivalent combination of experience and training.
Basic knowledge of assembly techniques methods materials fixturing and construction.
Ability to follow and communicate complex written and verbal instructions and to perform arithmetic calculations.
Demonstrated high degree of manual dexterity.
Ability to lift and/or maneuver objects weighing thirty to fifty pounds and occasionally up to one hundred twenty five pounds.
Ability to work in conditions which may include exposure to noise fumes crowding awkward physical positions abrasions cuts and chemicals.

MAJOR PLANT DIFFERENCES: