Electronic Measurement Equipment Mechanic

As a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC WGthis position is located in the Joint Forces Headquarters State Logistics Directorate (J-4) Surface Maintenance Facility. The primary purpose of this position is to perform calibration diagnostics repair and certification of electronic mechanical and radiation Test Measurement and Diagnostic Equipment (TMDE).

(1) Calibrates and repairs TMDE within support capability and authority including various levels of calibration as designated in technical bulletins manuals etc. Performs functional electronic physical and radioactive testing involving interpretation and analysis of measurement data in accordance with cyclic inspection requirements. Aligns troubleshoots tests inspects repairs modifies calibrates and certifies precision measurement equipment such as multimeters microwave equipment oscilloscopes temperature analyzers mercurial barometers gage blocks and micrometer caliper dimensional equipment digital voltmeters signal generators torque wrenches pressure gauges torque testers weight scales electronic counters radiation monitors radix calibrators and radiation dosimeters. Analyzes and isolates component malfunctions; calculates and determines tolerances; and performs tests and calibrations in accordance with instructions which are often vague and incomplete and may require the preparation of diagrams and instructions to facilitate the calibration action.

(2) Sets up system test sets and various types of test equipment such as frequency meters standing wave ratio meters radio frequency (RF) power meters function/ arbitrary waveform generator distortion analyzers time frequency work stations oscillators voltmeters electronic counters oscilloscopes attenuators decade resistors and capacitors signal generators stroboscope tachometers pneumatic and hydraulic pressure standards and other physical and electronic tests. Diagnoses equipment makes repairs and replaces defective parts/components such as integrated circuits printed circuit boards electronic condition coils radiation detector boards/circuits crystals transistors tubes transformers condensers diodes relays potentiometers and related components.

(3) Following repair tests by applying signals in known amplitude and wave shape into oscilloscopes to observe wave pattern. Isolates faults by taking measurements and comparisons in voltage amperage ohms henries power factor watts temperature humidity microns foot-pounds decibels sensitivity noise stability Voltage Standard Wave Ratio (VSWR) impedance phase absolute pressure time intervals displacement flow rate etc. to determine performance of equipment. If signal is distorted traces it through electronic stages to locate malfunctioning part. Checks sweep rate by feeding known signal to an oscilloscope and observing wave pattern to correct shape and size. Operates equipment to complete range checking for proper operation of positioning controls.

(4) Determines purpose in operation characteristics of each major section. Refers to technical manuals and manufactures specifications to obtain information on operation characteristics of circuit components such as integrated circuits microprocessors decoders latching networks notch filters logics controllers programmable gain amplifiers digital displays transistors tubes transformers coils relays motors and similar devices. Disassembles cleans and inspects parts such as printed circuit boards resistors capacitors integrated circuits relays chambers cables and wiring for evidence or wear or malfunction. Repairs and/or replaces parts as required.

(5) Completes necessary Army Maintenance Management System (TAMMS) calibration radiation reports and other records and forms on work completed. Ensures maximum number of weapons systems are operationally ready. Uses TMDE Integrated Maintenance Management Systems (TIMMS) for all supported equipment to track turn-in repair calibrate and return to the end user in a timely fashion to prevent work stoppages.

(6) Follows appropriate safety procedures with special care being exercised while calibrating high voltage radio frequency radioactive sources and high-pressure instruments and gages. Performs and interprets wipe tests on radiation sources for possibility of radiation hazards. Familiar with and abides by all Federal and State regulations concerning handling transportation and disposal of radioactive waste or devices.

(7) Performs other duties as assigned.

*The above description only mentions a limited amount of the positions official duties. For a full comprehensive document that covers all the duties of the position please contact one of the Recruitment Specialist at the bottom of the announcement.

Conditions of employment

• National Guard Membership is required.
• Males born after 31 December 1959 must be registered for Selective Service.
• Participation in direct deposit is mandatory.
• U.S. citizenship is required.
• This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.
• The duties of this job may significantly impact the environment. You are responsible to maintain awareness of your environmental responsibilities as dictated by legal and regulatory requirements your organization and its changing mission.
• Must be able to establish effective professional working relationships with coworkers and customers contributing to a cooperative working environment and successful accomplishment of the mission.
• May occasionally be required to work other than normal duty hours; shift work and/or overtime may be required.
• Federal employment suitability required and determined by a background investigation before appointment to position.
• May be required to successfully complete a trial period.
• Must have a valid drivers license.
• Must be able to obtain/maintain the necessary security clearance for the position.
• Incumbent of this position may be required to participate in a Medical Surveillance Program to evaluate exposure to potentially harmful physical and/or chemical agents. This may require pre-employment and yearly physical examinations.
• Military Assignment Requirement: Open to Enlisted members only.

Qualifications

Areas of Consideration:
Area 1 - Current permanent and indefinite T32 technicians of the Oregon ARNG.
Area 2 - Current permanent and indefinite T5 employees of the Oregon ARNG.
Area 3 - Current service members in the Oregon ARNG.

GENERAL and SPECIALIZED EXPERIENCE QUALIFICATION REQUIREMENTS:
Work involved in the maintenance repairs calibration and certification of electronic test measurement and reference equipment used for precise measurement of a variety of electrical and electronic values. Quantities and relationships such as voltage resistance capacitance frequency and inductance. Experience or training which demonstrates a working knowledge of electronic principles involved in the generation and measurement of such elements as voltage current impedance capacitance frequency and inductance. Experience in the use of various precision measurement instruments and standards.

Must have 18 months of experience or training with basic application of operating principles such as the production and utilization of oscillations over a broad range of frequencies; signal and waveform behavior distortion and amplification; pulse trigger and synchronization techniques; digital/analog processing and data conversion techniques; and a variety of display and indication methods. Experience in tracing signals and voltage paths and skilled in the analysis of waveform characteristics such as timing duration frequency and phasing. Originates test set-ups to isolate malfunctions and check performance characteristics of special or unique test panels or mockups. Experience in interpreting and applying a variety of technical electronic information such as schematic symbols mathematical expressions and formulas calibration procedures and other reference materials. Experience in applying established techniques and methods of repair testing alignment and calibration of equipment which serves as test equipment or precision measurement standards. Experience in utilizing electronic circuits to measure electronic or electrical quantities to determine the performance characteristics and accuracy of other instruments and equipment.